a standard penetration test (spt) was performed at a depth of 10 ft in sand of unit weight 120 lb/ft 3 . the n-value was found to be 26. determine the corrected n-value by the two methods presented in this chapter

To determine the required insulation thickness, you will need to use the heat transfer equation, which states that the rate of heat transfer through a material is equal to the product of the heat transfer coefficient, the surface area of the material, and the temperature difference between the two sides of the material.

The temperature difference between the chilled water and the ambient air is 30°C - 8°C = 22°C.

The surface area of the pipe is given by the formula for the surface area of a cylinder:

A = 2πrL

where:

r = the radius of the pipe

L = the length of the pipe.

The radius of the pipe is 5 cm / 2 = 2.5 cm = 0.025 m.

The surface area of the pipe is therefore A = 2π(0.025 m)(150 m) = 7.85 m²

The heat transfer rate through the insulation is given by: Q = (kA)(ΔT)/d, where:

Q= the heat transfer rate,

k = the thermal conductivity of the insulation,

A = the surface area of the pipe,

ΔT = the temperature difference between the chilled water and the ambient air,

d = the thickness of the insulation.

Rearranging this equation to solve for d, the thickness of the insulation, we get:

d = (0.05 W/m·°C)(7.85 m²)/(9 W/m²·°C)(22°C) = 0.03 m = 3 cm.

Therefore, the required thickness of the insulation is 3 cm.

Learn more about heat energy: https://brainly.com/question/25384702

#SPJ4

A) Illustration of the power circuit with a control block diagram for the inverter and dynamic brake is given in attachment.

B) [tex]T_{Break}=224.0128K N-m[/tex]

Any electrically powered circuit that drives a load falls under the definition of a power circuit. Although it may seem overly straightforward, it is crucial to distinguish between power and control circuits because of the distinct functions they serve.

A good example of a power circuit is one that has a motor as the load and an outlet as the source, two wires as the path, and a switch as the control device. The motor starts to turn when the switch is closed, allowing the flow of electrons to occur.

These electrons pass directly through the motor windings and start the motor. This circuit's switch, which is wired in direct series with the motor, is the only control device. This power circuit is not connected to any additional control circuits.

Learn more about power circuit

https://brainly.com/question/18799652

#SPJ4

(a) It will take about 4.8e-5 seconds for the surface to reach a safe-to-touch temperature of 42 °C.

(b) The corresponding temperature at the plastic/wood interface will be 200 °C, since this is the initial temperature and the interface is assumed to be adiabatic.

To solve this problem, we need to use the heat equation, which describes how heat flows through a material:

∂T/∂t = α ∂²T/∂x²

where T is the temperature, t is time, x is position, and α is the thermal diffusivity.

To solve this equation, we need to know the boundary conditions and initial conditions. In this case, the boundary conditions are the surface temperature (42 °C) and the temperature at the plastic/wood interface (200 °C). The initial condition is the initial temperature distribution, which is uniform at 200 °C.

First, let's find the convective heat transfer coefficient, k, using the relationship:

h = k / d

where d is the thickness of the plastic coating and k is the thermal conductivity.

Substituting the values given in the problem, we find that

k = 0.05 W/m-K.

Now, let's solve the heat equation using these values. To do this, we need to rearrange the equation to solve for t:

∂T/∂t = α ∂^2T/∂x^2

∂t = (α ∂^2T/∂x^2) / ∂T

t = ∫ (α ∂^2T/∂x^2) / ∂T dx

We can simplify this equation by assuming that the temperature change across the thickness of the plastic coating is small, so that ∂^2T/∂x^2 can be approximated as T''/d^2. Substituting this and the values for the other parameters gives us:

t = ∫ (α T''/d^2) / ∂T dx

= ∫ (α / k) dx

= (α / k) x

To find the time it takes for the surface to reach a safe-to-touch temperature of 42 °C, we need to solve for the time it takes for the temperature at the surface to drop from 200 °C to 42 °C. Substituting these values and the values for the other parameters gives us:

t = (1.2e-7 m2/s / 0.05 W/m-K) (2 mm)

= 4.8e-5 s

Learn more about heat energy: https://brainly.com/question/25384702

#SPJ4

Note that a milling machine can do all of the following tasks except: " ream a highly accurate hole with a fine finish" (Option D).

A milling machine is a tool that is used to machine flat and contoured surfaces, and it can also be used to rotate a multitoothed cutter into the workpiece to remove material. It is also capable of machining threads, gears, and spirals.

However, a milling machine is not typically used to ream holes, as reaming is a finishing operation that is usually done with a reamer, which is a specialized tool designed for this purpose. Reaming is used to create highly accurate holes with a fine finish, and it is typically done after the hole has been drilled or milled to its rough size.

There are several advantages to using a milling machine, including:

Versatility: Milling machines can be used to machine a wide range of parts and materials, including flat and contoured surfaces, threads, gears, and spirals.

Precision: Milling machines are capable of producing highly precise parts, as they can be accurately positioned and controlled using computer numerical control (CNC) technology, etc.

Learn more about milling machines:
https://brainly.com/question/23275945
#SPJ1

The statement that would be true about a critical path is; "All the Above" (Option D)

A critical path is the sequence of activities in a project that must be completed on time in order for the project to be completed on schedule. It is the longest path through the project, from start to finish, and includes the activities that have the least amount of scheduling flexibility. These activities are considered "critical" because any delay in their completion will directly impact the overall completion date of the project.

The critical path is important because it helps project managers identify the most important tasks in the project and allocate resources accordingly.

Learn more about Critical path:
https://brainly.com/question/16519233
#SPJ1

This FedEx error indicates that the selected FedEx service is not allowed for the shipment's destination country. To resolve this error, select a different carrier service. View the FedEx services available with ShippingEasy.

You may send items up to 150 lbs., 108" in length, and 165" in length with girth using FedEx Ground® and FedEx Home Delivery® Services. If the shipment weights more than 75 lbs, place yellow and black safety heavyweight labels over the diagonal corners. Only when instructed to do so by the sender or by FedEx policy must you sign for a shipment. You can check the tracking details that were sent to you via email from the sender or input the package's tracking number on fedex.com to find out whether your shipment needs a signature.

To learn more about FedEx error click the link below:

brainly.com/question/29376073

#SPJ4

GANs have proven helpful for semi-supervised learning, fully supervised learning, and reinforcement learning despite being initially presented as a type of generative model for unsupervised learning.

In June 2014, Ian Goodfella and his colleagues created a family of machine learning frameworks known as generative adversarial networks (GANs). One neural network gains at the expense of the other in a zero-sum game between two neural networks.

This method learns to produce fresh data with the same statistics as the training set given a training set. For instance, a GAN trained on images can produce new images with numerous realistic features that, at least on the surface, appear to be created by humans. GANs have proven helpful for semi-supervised learning, fully supervised learning, and reinforcement learning, while being initially presented as a type of generative model for unsupervised learning.

Know more about GANs here:

https://brainly.com/question/30072351

#SPJ4

The complete question is:

Unsupervised representation learning with deep convolutional generative adversarial networks. is the meaning of?

The emphasis of today's job search is on the needs of the employer.

An employer plays a wide range of roles. Being up to date and fostering a work environment that promotes employee satisfaction means understanding what it means to be an employer today.

The definition of an employer is a person or a group operating in the public, private, nonprofit, or commercial spheres that employs and compensates workers. The employer, who holds the position of authority within an organisation, establishes the conditions of employment for workers and provides the negotiated terms, such as the salary.

A person who shapes an organization's culture is another way to describe an employer. Employers have the power to make a strong statement about the hierarchy within the workplace and how employees should interact with one another through their actions.

Learn more about Employers

https://brainly.com/question/26463698

#SPJ4

Answer:

18

Explanation:

18 hours awake = same effect as .07 blood alcohol concentration

Below is the C++ code for the given problem in which we are analyzing the Problem of the Gunter’s Mountain Shop.

Coding Part:

#include <iostream>

#include <iomanip>

using namespace std;

int main()

{

  // print "Architect Area Calculator"

  cout << "Architect Area Calculator:" << endl;

  cout << "*****************************" << endl;

  // print menu options

  cout << "1. Rectangle \n2. Triangle \n3. Circle \n4. Quit\n" << endl;

  // ask user to enter a menu item in the range 1-4

  cout << "Please enter a menu item (1-4) > ";

  // declare a variable to store user's choice

  int item;

  // read a user's choice of menu item

  cin>>item;

  // if the user entered item is valid i.e it is the range 1-4, then proceed further

  if(item >= 1 && item <= 4)

  {

      // if user's choice of menu item is 1

      if(item == 1)

      {

          // declare 2 double variables to store length and width of a rectangle respectively

          double length, width;

          // print "Rectangle"

          cout << "\n\nRectangle" << endl;

          // ask user to enter length of the rectangle

          cout << "Please enter the length > ";

          // read length of rectangle from user

          cin >> length;

          // check if the length of the rectangle is non-positive, if not positive then

          if(length <= 0)

          {

              // print an error message

              cout << "\nError : Length of the rectangle should be positive.\n" << endl;

              // stop program by returning 0

              return 0;

          }

          // ask user to enter width of the rectangle

          cout << "Please enter the width > ";

          // read width of the rectangle from user

          cin >> width;

          // check if the width of the rectangle is non-positive, if not positive then

          if(width <= 0)

          {

              // print an error message

              cout << "\nError : Width of the rectangle should be positive.\n" << endl;

              // stop program by returning 0

              return 0;

          }

          // calculate area of rectangle using given formula, and print area with 2 decimal precisions

          cout << "\n Area = " << fixed << setprecision(2) << (length * width) << " sq/ft\n" << endl;

      }

      // if user's choice of menu item is 2

      else if(item == 2)

      {

          // declare 2 double variables to store base and height of a triangle respectively

          double base, height;

          // print "Triangle"

          cout << "\n\nTriangle" << endl;

          // ask user to enter base of the triangle

          cout << "Please enter the base > ";

          // read base of the triangle from user

          cin >> base;

          // check if the base of the triangle is non-positive, if not positive then

          if(base <= 0)

          {

              // print an error message

              cout << "\nError : Base of the triangle should be positive.\n" << endl;

              // stop program by returning 0

              return 0;

          }

          // ask user to enter height of the triangle

          cout << "Please enter the height > ";

          // read height of the triangle from user

          cin >> height;

          // check if the height of the triangle is non-positive, if not positive then

          if(height <= 0)

          {

              // print an error message

              cout << "\nError : Height of the triangle should be positive.\n" << endl;

              // stop program by returning 0

              return 0;

          }

          // calculate area of triangle using given formula, and print area with 2 decimal precisions

          cout << "\n Area = " << fixed << setprecision(2) << (height * base)/2 << " sq/ft\n" << endl;

      }

      // if user's choice of menu item is 3

      else if(item == 3)

      {

          // declare a double variable to store radius of a circle

          double radius;

          // print "Circle"

          cout << "\n\nCircle" << endl;

          // ask user to enter radius of the circle

          cout << "Please enter the radius > ";

          // read radius of the circle from user

          cin >> radius;

          // check if the radius of the circle is non-positive, if not positive then

          if(radius <= 0)

          {

              // print an error message

              cout << "\nError : Radius of the circle should be positive.\n" << endl;

              // stop program by returning 0

             return 0;

          }

          // calculate area of circle using given formula, and print area with 2 decimal precisions

          cout << "\n Area = " << fixed << setprecision(2) << (3.14 * radius * radius) <<" sq/ft\n" << endl;

      }

      // if user's choice of menu item is 1

      else if(item == 4)

      {

          // print thank you message and exit

          cout << "\n\nThank you for using Architect Area Calculator..." << endl;

      }

  }

  else

  {

      // if user's choice of menu item is not in the range 1-4, then print an error message and exit

      cout << "\nError : Menu item should be in the range 1-4\n" << endl;

  }  

}

To know more about C++ code, visit: https://brainly.com/question/27019258

#SPJ4

Special shapes are used in flowcharts to depict various kinds of operations or steps in a process. The order of the steps and their interactions are depicted with lines and arrows. Symbols for flowcharts are those. Thus, option D is correct.

Data Flow – An arrow sign, which denotes the direction of flow, is used to represent the movement of data between external entities, procedures, and data stores.

Therefore, a data flow uses various symbols and shapes to represent data flow, processing, and storage.

Learn more about data flow here:

https://brainly.com/question/15517161

#SPJ1

Technician b is correct. According to Technician B, the majority of engine bearings have an aluminum shell for strength and are covered in a tin-lead alloy.

For street and performance engines, the generally acknowledged norm that most crankshaft manufacturers prefer is 0.0010-inch for every 1-inch of journal diameter. Therefore, the bearing clearance for a 2.45-inch small-block main journal would be 0.0024-inch.

The crankshaft journal's outer diameter is measured using callipers. A dial bore gauge is used to measure the bearings' inner diameter. Both rod bearings and main bearings are measured with the bearings mounted in the respective connecting rods and main bores, respectively.

A thin calibrated plastic strip serves as a plastic gauge. It can be used to measure gaps and monitor bearing clearance. It is utilized at locations on crankshaft or connecting rod bearings where a micrometre measurement is required quickly.

Know more about engines here:

https://brainly.com/question/14234029

#SPJ4

if your vehicle skids, take your foot off of the gas pedal, but do not hit the brakes unless you are about to hit something is true.

if your vehicle skids, the first thing you should do is to take your foot off the gas pedal and steer in the direction you want the front of the vehicle to go.

This will help you regain control of the vehicle. If you hit the brakes while the wheels are skidding, it can cause the wheels to lock up, which can make the skid worse and lead to a loss of control. If you are about to hit something, such as a curb or another vehicle, it may be necessary to brake in order to avoid a collision.

However, it is generally best to avoid braking during a skid if possible, as this can cause the skid to become more severe.

Learn more about vehicle skids from

https://brainly.com/question/4360615

#SPJ1

See full question below

if your vehicle skids, take your foot off of the gas pedal, but do not hit the brakes unless you are about to hit something. true or false

After assuming all unshown dimensions are the same as in the previous question the Overall mass is 666.04 grams

The least amount of coordinates required to specify each point within a mathematical space or object is known as its dimension. A line therefore has a dimension of one since only one coordinate is required to identify a point on it, such as the point at 5 on a number line. In order to specify a point on a surface, such as the perimeter of a cylinder or sphere, two coordinates are needed; for instance, both a latitude and a longitude are needed to pinpoint a point on the surface of a sphere. This gives surfaces, like the boundaries of these objects, a dimension of two (2D). A space on the plane with two dimensions is called a Euclidean space.

To learn more about dimension click here

brainly.com/question/28688567

#SPJ4

Note that it is TRUE to state that the Index -1 Identifies the last character of a String.

A string is generally a sequence of characters in computer programming, either as a literal constant or as some form of variable. The latter can have its components modified and its length changed, or it can be set (after creation).

A string's first character corresponds to index 0, and its last character relates to index (length of string)-1. The amount of characters in a string, including spaces, punctuation, and control characters, is referred to as its length.

Learn more about index in programming:
https://brainly.com/question/14895144
#SPJ1

It is to be noted that in OSHA, reducing time lost due to injuries and accidents can lead to increased productivity and efficiency, improved financial performance, and better employee morale and retention.

The Occupational Safety and Health Act of 1970 established the Occupational Safety and Health Administration (OSHA) to safeguard employees' safety and health by creating and enforcing standards and providing training, outreach, information, and support.

Reducing time lost due to injuries and accidents can have a number of advantages for a business. By reducing injuries and accidents, a firm may save time and money on absenteeism, medical care, and workers' compensation claims. This can lead to enhanced production and efficiency, which can contribute to better financial performance.

Learn more about OSHA:
https://brainly.com/question/29345131
#SPJ1

Depending on whether Hi is greater than or equal to MD, the ALU either subtracts the MD register (the divisor) from its Hi input or allows the Hi input to pass through unaltered.

In conclusion, the division and multiplication operations used in this project are performed by the Arithmetic Logic Unit (ALU), which is an arithmetic and logical operation.

two binary values can be multiplied using this procedure. Take into account the fact that the ALU only offers the addition and shifting operations, not the multiplication operation. The microprogramming code can then be stored in memory and used to perform multiplication operations.

To know more about Arithmetic Logic Unit visit :-

https://brainly.com/question/28548014

#SPJ4

After running the code of the given Oz program, some errors are displayed. That is because delay time is not assigned to Y.

What exactly is a Oz program?

Oz is a multi-paradigm programming language intended for advanced, concurrent, networked, soft real-time, and reactive applications. State, abstract data types, objects, classes, and inheritance are among the key features of object-oriented programming provided by Oz.

Compositional syntax, first-class procedures/functions, and lexical scoping are among the key features of functional programming. It includes logic variables, constraints, disjunction constructs, and programmable search mechanisms, as well as the key features of logic programming and constraint programming.

It enables users to create an unlimited number of sequential threads dynamically. The threads are dataflow threads in the sense that when performing an operation, the thread will suspend until all operands required have a well-defined value.

To know more about Oz program, visit: https://brainly.com/question/29891462

#SPJ4

If you have a goal statement or a sentence describing the mini-world of your database, how can you start working out the relationships between entities you will need to Look for adjectives.

Define a database.

An organized group of data that is electronically accessible and stored is referred to as a database in computing. Small databases can be kept on a file system, whereas large databases are kept on computer clusters or in the cloud. Any grouping of data or information that has been carefully structured to allow quick computer search and retrieval is referred to as a database, sometimes known as an electronic database.

In order to make it easier to store, retrieve, modify, and delete data while carrying out various data-processing tasks, databases are designed in this manner. For the purpose of storing and retrieving data, databases are collections of data. Data in the database can be found in numeric, alphabetical, or alphanumeric forms.

To learn more about a database, use the link given
https://brainly.com/question/28033296
#SPJ4

Answer:

The combination mentioned below is being burned at 1000°C for 2.1 seconds with 50% surplus air. This waste's primary organic hazardous constituents (POHCs) include benzene, chlorobenzene, and toluene. At dry standard conditions, the flow rate of gas from the incinerator is 450 m3/min. The mole fraction of O2 in the stack gas is 14%. a) Determine if this emission meets requirements for - POHCs Particulates HCl b) Comment on the results Inlet (kg/h) 2015 1150 Outlet (kg/h) 0.537 0.109 Compound Benzene Chlorobenzene, C6H5C1 Toluene Xylene HC1 Particulates 637 3040 0.022 1.25 10.7 2.5 Molar mass of HCl: 36.5 g/mol P. = P. (21-X) (21-Y) X: mole fraction of O2 corrected to the dry conditions Y: mole fraction of O2 in the stack gas

The variable that is used for flow control services is Buffer window .

For output in a console window, a screen buffer is a two-dimensional array of character and colour data. There may be several screen buffers on a console. The screen buffer that is visible is the current screen buffer. Every time a new console is created, the system builds a screen buffer.

A memory area known as a buffer is used to store data momentarily while it is being transferred from one location to another. When transferring data between computer processes, a buffer is employed. The vast majority of buffers are used in software.

To learn more about Buffer window refer to :

https://brainly.com/question/9906723

#SPJ1

A program that reads an integer as input and points the hailstone sequence starting with the integer entered is mentioned as below.

Computer programming is the method of carrying out a certain computation, often through creating and constructing an executable computer program.

Programming activities include analysis, algorithm generation, algorithm accuracy and resource use assessment, and algorithm implementation.

CODE IN PYTHON:

def haleStoneSeq(num):  ## method to that return the hailStoneSquence

   NumberList = [num]

   while num != 1:

       if (num%2) == 0:

           num = num//2

           NumberList.append(num)

       else:

           num = (num * 3) + 1

           NumberList.append(num)

   return NumberList

n=int(input("Enter the input value : "))   ## asking the input from the user

print(haleStoneSeq(n))   ## method calling

Learn more about programming here:

https://brainly.com/question/11023419

#SPJ4

To add a method calculate pay() to the employee class. the method should return the amount to pay the employee by multiplying the employee's wage and number of hours worked, check the code given below.

In object-oriented programming, a class is a template definition of the method(s) and variable(s) in a particular kind of object. As a result, an object is a unique instance of a class and contains real values rather than variables.

The class is one of the core ideas in object-oriented programming. The following are some essential ideas about classes:

A class's subclasses are able to take on all or some of its parent class's characteristics. In relation to each subclass, the class becomes the superclass.

Subclasses can define their own methods and variables independently of their superclass as well.

The term "class structure" refers to the relationship between a class and its subclasses.

//CODE//

class Employee:

    def __init__(self):

        self.wage = 0

        self.hours_worked = 0

     def calculate_pay(self):

        return self.wage * self.hours_worked

  alice = Employee()

alice.wage = 9.25

alice.hours_worked = 35

print('Alice:\n Net pay: %f' % alice.calculate_pay())

 bob = Employee()

bob.wage = 11.50

bob.hours_worked = 20

print('Bob:\n Net pay: %f' % bob.calculate_pay())

Learn more about class

https://brainly.com/question/9949128

#SPJ4

One of these important innovative advances is the use of electric switches to control electricity. Rotary Switch is the name of a certain type of rotary switch that moves in a circular motion and controls the circuit. Thus, option C is correct.

Switches. The most frequent way to control electrical circuits is through switches. By opening or closing the circuit, switches control a circuit. Manual, hydraulic, electrical, and pneumatic methods can all be used to operate switches.

Therefore, Fully automated machines require a Continuous-cycle reciprocation circuit.

Learn more about automated machines here:

https://brainly.com/question/24198010

#SPJ1

Using the knowledge of computational language in python it is possible to write a code that first line contains an integern, the number of students.

#include<bits/stdc++.h>

using namespace std;

const int Mx=1e5+5;

int par[Mx],cnt[Mx];

void ini(int n){

   for(int i=1;i<=n;++i)par[i]=i,cnt[i]=1;

}

int root(int a){

   if(a==par[a])return a;

   return par[a]=root(par[a]);

}

void Union(int a,int b){

   a=root(a);b=root(b);

   if(a==b)return;

   if(cnt[a]>cnt[b])swap(a,b);

   par[a]=b;

   cnt[b]+=cnt[a];

}

int* getTheGroups(int n,int q,int sz,string queryTypes[],int student1[],int student2[],int* ans){

   ini(n);

   int current=0;

   for(int i=0;i<q;++i){

       if(queryTypes[i]=="Friend"){

           Union(student1[i],student2[i]);

       }

       else{

           int x=root(student1[i]),y=root(student2[i]);

           if(x==y)ans[current++]=cnt[x];

           else ans[current++]=cnt[x]+cnt[y];

       }

   }

   return ans;

}

int main(){

   int n,q,sz=0;

   cin>>n>>q;

   string queryTypes[q];

   int student1[q],student2[q];

   for(int i=0;i<q;++i){

       cin>>queryTypes[i];

       if(queryTypes[i]=="Total")

           ++sz;

   }

   cin>>q;

   for(int i=0;i<q;++i)cin>>student1[i];

   cin>>q;

   for(int i=0;i<q;++i)cin>>student2[i];

   int ans[sz];

   int* ptr=getTheGroups(n,q,sz,queryTypes,student1,student2,ans);

   for(int i=0;i<sz;++i)

       cout<<ptr[i]<<endl;

   return 0;

}

See more about python at brainly.com/question/18502436

#SPJ1

Amazon web services (aws) provide numerous benefits, including increased scalability, dependability, and security. was introduced in response to rival efforts by leading computing behemoths Microsoft.

What is Amazon web services (aws)?

Amazon Web Services (AWS) is the most comprehensive and widely used cloud platform, offering over 200 fully featured services from data centers worldwide. Millions of customers, including the fastest-growing startups, largest enterprises, and leading government agencies, rely on AWS to reduce costs, improve agility, and accelerate innovation.

AWS provides more services and features within those services than any other cloud provider, ranging from compute, storage, and databases to emerging technologies such as machine learning and artificial intelligence, analytics and data lakes, and the Internet of Things (IoT).This makes it faster, easier, and less expensive to migrate your existing applications to the cloud and build almost anything you can think of.

To learn more about Amazon web services (aws), visit: https://brainly.com/question/14014995

#SPJ4

Computer Eng and Civil Eng consist of Algorithms, programming and statistics and Mechanics, fluid mechanics and strength of material respectively. So your should learn more about Computer Eng and Civil Eng.

A civil engineer is a professional who specialises in the planning, designing, building, maintaining, and operation of infrastructure while safeguarding the public's and the environment's health. They may also work to improve already-existing infrastructure that has been left unattended.

In order to plan, design, supervise construction of, and maintain building structures and facilities, such as roads, railroads, airports, bridges, harbours, channels, dams, irrigation projects, pipelines, power plants, and water and sewage systems, civil engineering, one of the oldest engineering disciplines, deals with the built environment.

John Smeaton coined the term "civil engineer" in 1750 to distinguish between engineers who worked on civil projects and those who worked for the military and built armaments and defences.

Learn more about civil engineering

https://brainly.com/question/25840283

#SPJ4

The time to achieve a grain diameter of 5.5 × 10⁻² mm is 477 minutes

A straight line passes through the middle of a rounded object or shape and emerges at the opposing edge.

We have to calculate the K

Given that the grain diameter exponent (n) = 2.2

Grain diameter (d) = 5.6 × 10⁻² mm = 5.6 × 10⁻⁵ m

d₀ =  2.4 × 10⁻² mm =  5.6 × 10⁻⁵ m

t = 500 min

[tex]K = \dfrac{d^n - d^n\circ}{t} \\\\K = \dfrac{(5.6 \times 10^-^5)^{2.2} - (2.4 \times 10^-^5)^2}{500} \\\\K = 7.48\times 10^{-13} m/min[/tex]

From K we can determine the time required based on the desired diameter grain diameter (d) = 5.5 × 10⁻² mm = 5.5 × 10⁻⁵ m

[tex]K = \dfrac{(5.6 \times 10^-^5)^{2.2} - (2.4 \times 10^-^5)^2}{7.8 \times 10^{-13}} \\\\K = 477 min.[/tex]

Therefore, the time is 477 minutes.

To learn more about diameter, refer to the link:

https://brainly.com/question/17045755

#SPJ1

To determine the expiration date of the last annual aircraft inspection, a person should refer to the aircraft maintenance records.

What are aircraft maintenance records?

Aircraft maintenance records include information about the work done to the aircraft, the date it was finished, the signature of the maintenance team, information about the FAA certificate, and the certificate number and signature of the person who put the aircraft back in service. The maintenance records mentioned in this rule can be simplified into two groups: permanent records and expiring records.

Permanent records are those maintenance logs that need to be retained and kept up-to-date for the aircraft forever. They act as a record of every maintenance action that has taken place during the lifecycle of the aircraft. It also functions as a tool for figuring out whether an aircraft has received all necessary maintenance and is in a state that allows for safe flight.

To learn more about aircraft maintenance records, use the link given
https://brainly.com/question/27961960
#SPJ4